Mechanical properties by type

Torsional breaking torque （Unit/N・m）
Type M1.7 M2 M2.6 M3 M4 M5 M6 M8 M10
 M12 M16
PC 0.02 0.05 0.12 0.22 0.54 1.03 1.37 2.94 5.90 10.30 -
PPS - 0.08 0.19 0.36 0.71 1.42 2.11 5.29 11.80 20.60 -
RENY 0.03 0.10 0.24 0.39 0.79 1.77 2.94 7.85 12.75 24.50 39.00
PEEK 0.02 0.06 0.16 0.30 0.64 1.28 2.26 5.98 10.80 18.60 -
PVC - - - - 0.33 0.60 0.96 2.17 4.36 8.57 -
PP - - - - 0.23 0.51 0.80 2.20 3.40 5.30 -
PTFE - - - 0.02 0.03 0.08 0.14 0.24 0.69 1.54 -
PFA - - - - 0.04 0.21 0.35 0.85 - - -
PVDF - - - 0.22 0.40 0.64 0.88 2.65 3.90 9.20 -
PA66   0.04 0.04 0.07 0.11            
Ceramic
spacer
(female) 		- - - 2 2.94 5.88 11.76 - - - -
PPS M1.7 M2 M2.6 M3 M4 M5 M6 M8 M10
 M12 M16
Low head (hexagonal) - - - 0.25 0.46 1.04 1.70 - - - -
Low head (hexalobular) - - - 0.29 0.48 1.07 2.00 - - - -
Ultra-low head (hexalobular) - - - 0.16 0.29 0.65 0.94 - - - -
Reny M1.7 M2 M2.6 M3 M4 M5 M6 M8 M10
 M12 M16
Low head (hexagonal) - - - 0.31 0.62 1.20 2.15 - - - -
Low head (hexalobular) - - - 0.38 0.75 1.55 2.57 - - - -
Ultra-low head (hexalobular) - - - 0.20 0.62 0.66 1.09 - - - -
PEEK M1.7 M2 M2.6 M3 M4 M5 M6 M8 M10
 M12 M16
Low head (hexagonal) - - - 0.15 0.54 1.11 1.72 - - - -
Low head (hexalobular) - - - 0.21 0.54 1.11 2.44 - - - -
Ultra-low head (hexalobular) - - - 0.15 0.50 1.09 1.71 - - - -
Tensile breaking load （Unit/N・m）
Type M1.7 M2 M2.6 M3 M4 M5 M6 M8 M10
 M12 M16
PC 47 112 227 300 515 750 1080 1470 3140 4710 -
PPS - 236 440 570 980 1570 2250 3720 5890 7850 -
Reny 80 303 588 635 1470 2450 3140 5100 6900 8700 18000
PEEK 59 160 312 430 765 1230 1670 3090 4900 7360 -
PVC - - - - 423 666 855 1605 2618 3823 -
PP - - - - 270 440 620 1100 1800 2400 -
PTFE - - - 61 104 161 240 418 654 835 -
PFA - - - - 106 175 261 482 - - -
PVDF - - - 107 314 640 940 1810 2700 3980 -
PPS M1.7 M2 M2.6 M3 M4 M5 M6 M8 M10
 M12 M16
Low head (hexagonal) - - - 492 789 1190 1811 - - - -
Low head (hexalobular) - - - 498 847 1287 1933 - - - -
Ultra-low head (hexalobular) - - - 278 499 604 937 - - - -
Reny M1.7 M2 M2.6 M3 M4 M5 M6 M8 M10
 M12 M16
Low head (hexagonal) - - - 740 1325 2050 2798 - - - -
Low head (hexalobular) - - - 850 1430 2050 3120 - - - -
Ultra-low head (hexalobular) - - - 365 697 1065 1604 - - - -
PEEK M1.7 M2 M2.6 M3 M4 M5 M6 M8 M10
 M12 M16
Low head (hexagonal) - - - 370 730 1170 1666 - - - -
Low head (hexalobular) - - - 375 744 1166 1665 - - - -
Ultra-low head (hexalobular) - - - 317 624 1146 1455 - - - -
Note: The numerical values above give typical values. These values are not guaranteed. Values may change due to usage conditions.
Values are calculated based on average values. Recommended fastening torque is 50% of breaking torque. (60% for ceramic only.)

To Top of Page